Slik at du ser klart uten å måtte lete lenge etter viktige dokumenter som bruksanvisninger og datablad kan du laste dem ned.

H14.2-H14R.2QUGNew logo170211smile Created Date: 2/11/2017 5:42:36 PM. Many of our models can also be powered by other energy sources – here is a list PDF. How does the USB port work? Some models have an external USB port built into the casing (H7.2 and H14.2). This port is a connector for the Ledlenser power bank (item number 7709).

Downloads

For flashlights

Car Lamp

D-Series

EX-Series

F-Series

iL-Series

K-Series

M-Series

Led Lenser Replacement Parts

Outdoor

P-Series

T-Series

X-Series

For headlamps

EX-Series

H-Series

i-Series

iL-Series

NEO Series

Outdoor

SEO Series

XEO Series

For worklights

i-Series

For floodlights

i-Series

For lanterns

i-Series

Lantern

Outdoor

Garanti for privatkunder

Service

Hos Ledlenser er det ikke bare lyktene som holder lenge, men også garantien.

Klikk for klikk til en passende Ledlenser

Produktrådgiver

Vårt lyktesortiment er like mangfoldig som menneskene som bruker det. Med noen få museklikk hjelper produktrådgiveren deg med å finne lykten som passer akkurat deg.

Opplysende svar på ofte stilte spørsmål

Ledlenser FAQs

Spørsmål er til for å bli stilt. Men noen har vi allerede svart på – i våre FAQs.

03

LED LENSER® * h14R

.2

When the headlamp is on, rotate the “Multi-

function Wheel' switch on the back to adjust the

LED brightness based on your needs. Turning

left: the brightness of white LED will getting

lower.Turning right: the brightness of white LED

will getting brighter (except the strobe function).

The LED will blink once to indicate the maximal

and minimum brightness.

d) Boost mode: in each setting, push the front

switch for 2 seconds, you will enter to boost

mode, after a short time the flashlight will

return to previous choosing.

All Light Functions above are in a loop. You can

change the functions by press the switch button.

Note: when switching between modes, press the

“Multi-function Wheel” switch no longer than 2

seconds, otherwise the product will turn off.

5.2 Light Program Red (rear light)

ON-OFF/ change the function within 2 seconds.

More than 2 seconds the lamp will turn off) /

charge indicator/ battery capacity indicator

function is available for the red LED:

1) ON-OFF function: in any status, two red LED

will light up by pressing the “Multi-function

Wheel” switch once: the LEDs will start to blink,

by pressing the switch twice; at the third push

the LEDs will turn OFF.

Led Lenser H14 User Manual Pdf File

2) Charge indicator function: the red LED will

glows when charging, after full charge, the LED

will glows green, please be noticed that the

white LED couldn’t working when charging;

3) Battery capacity indicator: when you start to

use white LED, the red LED on the battery box

will glows for 5 seconds and then off, green

means the battery capacity is 50%-100%; yellow

means the battery capacity is 20-49%; when the

red LED is glows means the battery capacity is

lower than 19%, it’s not suit for long time use,

you need to charge the battery.

6. Energy Modes

By selecting one of the two Energy Modes

Led Lenser H14 User Manual Pdf Online

(Energy Saving or Constant Current), you take

a decision on how the energy contained in the

accumulator respectively in the batteries is

used.

6.1 Energy Saving: The light output is controlled

by the integrated Smart Light Technology (SLT).

The brightness is matched to the real conditions

that occur during normal use of the lamp, thus

providing a longer burn time.

6.2 Constant Current: This Energy Mode allows

the continuous use of all the Light Functions

with a more or less constant light output. This

Energy Mode is to be preferred when a high

brightness level is more important than a long

Led Lenser Warranty

burn time

Changing of the Energy Modes

Changing the Energy Modes can only be done

when the flashlight is in Light Program White

and the lamp is turned Off. To change the energy

mode, with the white LED off, press the “Multi-

function Wheel” on the back 8 times, then on the

8th click keep the knob pressed for approx. 2-4

seconds. Then you change the mode between

„energy mode“ and „constant current mode“.

a) Constant current mode: In case the

brightness reduces immediately in 2 seconds,

the H14R.2 is on constant current mode;

b) Energy saving mode: in case the brightness

reduce gradually to zero, the H14R.2 is in the

Energy Mode.

With this procedure, you can switch between

the two Energy Modes. It is not possible to

determine in which Energy Mode the H14R.2

is. To find this out, you must carry out the

procedure. If the H14R.2 is thereafter not in the

desired Energy Mode any more, you must repeat

the procedure again. The flashlight will reset to

energy saving mode if you change the battery or

cut the power.

7. „Transport Lock“

When the H14R.2 switched Off, press the front

switch for approx. 5 seconds till the light turns

off in order to enable the “Transport Lock.” The

H14R.2 cannot be turned on any more, either

intentionally or unintentionally. Accidental

power consumption is not possible.

To deactivate the “Transport Lock”, just press

the front switch again for 5 seconds. The

headlamp will now return to the Light Program.

Led Lenser H14.2 Manual

8. Reset function

If the Accumulator-Pack, the alkaline batteries

are taken out the battery box you have 'reset'

the H14R.2. You have thus reset a few functions:

The „Transport Lock“ (see Point 7) is

deactivated.

The Light Function Dim (see Point 5.1) is set to

low brightness.

As Energy Mode Energy Saving is active (see

Point 6).

Led Lenser T7 Flashlight

The Light Program White (see Point 5.1) is

activated.

9. Charging

The H14R.2 indicates by the flashing of the

white LED that it is running out of energy in

near future. Please charge the Accumulator-

pack in time. Charge the Accumulator-pack of

your H14R.2 in a dry place and only by using the

charger that is included in the delivery or by a

USB port (see below).

The following information applies only to the

included accessories. You cannot charge any

other accumulators or batteries in the H14R.2.

In case Li-ion Accumulators are used, they must

be charged in approved external chargers.

In the scope of delivery of the H14R.2 there

is a plug and a charger. In case both are not

connected already please connect them so that

the connection clicks.

The charger of H14R.2 has a USB port, which

must be connected with the corresponding

port at the supplied charging cable in order to

Led Lenser H14 User Manual Pdf 2 10

charge Accumulator-pack. The other side of the

charging cable (micro USB) must be connected

to the micro USB port on the battery box.

The last step is to connect the plug into a socket

(Input: 100 V to 240 V / 50 Hz to 60 Hz). When

Led Lenser M7r

charging is completed (after maximum 4 to

5 hours), unplug the charger from the socket